Blognasium

An Exercise In Comunications

News Feed

Recent Users

Recent Albums

Leaderboard
1
ramblindan
ramblindan
492 Points
2
Drumguy
Drumguy
72 Points
3
shelbelle72
shelbelle72
54 Points
4
emmoonis
emmoonis
30 Points
5
tester
tester
27 Points
View Leaderboard

Recent Updates

Pinned Items
Recent Activities
  •   ramblindan commented on this post about 3 hours ago
    Making a dozen or more 3D printed fozzle fish keyfobs. They're back in demand for the UV change version. Take them in the sun (UV Radiation) and they almost immediately change from white to dark violet. Change back to white in a few seconds back... Making a dozen or more 3D printed fozzle fish keyfobs. They're back in demand for the UV change version. Take them in the sun (UV Radiation) and they almost immediately change from white to dark violet. Change back to white in a few seconds back out of the sunshine. I am making some glow in the dark too. The UV PLA plastic is out of stock so it may be difficult to get more. More
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  • The Ramblin' Dan's Store has been going crazy with new orders. It has been slow all summer with just small parts sales, but suddenly in the last week, people must be getting ready for a winter building session in their workshops. New lathes and... The Ramblin' Dan's Store has been going crazy with new orders. It has been slow all summer with just small parts sales, but suddenly in the last week, people must be getting ready for a winter building session in their workshops. New lathes and mills are on high demand. Two of each in one week. I am happy people are doing more than 3D printing. Nice sales week for me. More
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  • I have adjusted the permissions of non-registered viewers. That is so they can become very low level users. They can now make or add comments to the Blog and Discussion areas, but they must register to make original postings. This may make... I have adjusted the permissions of non-registered viewers. That is so they can become very low level users. They can now make or add comments to the Blog and Discussion areas, but they must register to make original postings. This may make Blognasium seem a bit more friendlier. Not expecting a flood... heh... More
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  • Presently working on more lost wax casting. I have a couple of new silver pieces in the kiln for casting about noontime. I also have om piece I am going to cast is brass. I tried brass once before and I had a bad (cracked) mold. It was a... Presently working on more lost wax casting. I have a couple of new silver pieces in the kiln for casting about noontime. I also have om piece I am going to cast is brass. I tried brass once before and I had a bad (cracked) mold. It was a disaster. I am hoping it goes well this time. I'd like to do heavier and larger pieces that would just be to expensive in silver. Silver is up about $4,00 an ounce from just a few months ago. Brass is low cost. More
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  •   ramblindan commented on this post about 1 week ago
    For some reason my status posts don't appear here unless I am logged in. I can't (yet) find where I may have turned off letting non registered guest see my status. Can you see this post without logging in?
    • ramblindan
      OK... Found the problem. I had this (my) name listed as an administrator, which is a classification I had set to "not show" to unregistered viewers. FOK... Found the problem. I had this (my) name listed as an administrator, which is a classification I had set to "not show" to unregistered viewers. Fixed it!  More ...
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  • shelbelle72
    shelbelle72 is now friends with Drumguy
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
  • I purchased a new filament for 3D printing Amazon now has their own brand. I decided to see how it worked in my printer. I got some dark prown and printed this puppy.
    Post is under moderation
    Stream item published successfully. Item will now be visible on your stream.
Activities are currently restricted to members only.

Log in to see what's going on.
Unable to load tooltip content.